Formation and wear mechanism of nickel titanium intermetallics during heat treatment of nickel coating on Ti-6Al-4V substrate

In the present work, inter-diffusion of nickel and titanium and formation of Ni-Ti intermetallic compounds on Ti-6Al-4V substrate have been studied. Initially, nickel was electrodeposited on the alloy using a modified Watts bath solution at a current density of 2 A dm^?2 for 1?h. The coated specimens were then heat treated for different durations at 750, 800 and 850 °C under argon atmosphere. The effects of temperature and time on the characteristics, hardness and wear resistance of intermetallic phases were investigated. The results showed that a multilayer structure was formed after heat treatment, an outer layer of residual nickel, an area of intermetallic layers with different compositions followed by a solid solution of Ni-Ti. It was also observed that an increase in time or temperature at first led to the formation of thicker intermetallic layers; however, after passing a critical point, the intermetallic layers seem to dissolve into the substrate. Furthermore, the wear rates of the diffusion treated samples were four times lower compared to Ti-6Al-4V alloy when sliding against AISI 52100 hardened steel.     

柱塞卡滞原因分析

某柱塞泵工作中发生柱塞卡滞,经显微形貌观察、光谱分析、电子探针面扫描分析和显微硬度分析等,确定柱塞卡滞的根本原因为原材料组织中存在严重的网状共晶碳化物,降低了强度和韧性,增大了柱塞球面表层的脆性,进而导致了球面部位的接触疲劳抗力下降。严重的疲劳磨损与接触疲劳造成了柱塞球面脱层破坏,由此产生的金属碎屑进入柱塞与衬套的配合间隙处,进而限制了柱塞的自由运动。     

硼氢化钠对滑轮用铸钢板化学镀Ni-B合金薄膜性能的影响

在滑轮用铸钢板上化学镀Ni-B合金薄膜,并研究了硼氢化钠的质量浓度对化学镀Ni-B合金薄膜性能的影响。结果表明:适当增加硼氢化钠的质量浓度,有利于增大化学镀Ni-B合金薄膜的厚度及硼的质量分数,从而提高化学镀Ni-B合金薄膜的硬度。当硼氢化钠的质量浓度大于1.2 g/L时,硼氢化钠的水解速率加快及剧烈的析氢反应,导致化学镀Ni-B合金薄膜的厚度及硬度有所降低。当硼氢化钠的质量浓度为1.2 g/L时,化学镀Ni-B合金薄膜表面"胞状"颗粒均匀、致密,摩擦因数和磨损率最低,具有最佳的耐磨性。     

TC4合金表面Cu/石墨复合镀层的摩擦磨损行为

采用无氰电镀工艺在TC4合金表面制备了Cu/石墨复合镀层，研究了镀层的组织结构和摩擦磨损行为。结果表明，采用无氰电镀方法能够在TC4合金表面制备出组织致密且与基体结合紧密的Cu/石墨复合镀层，但增加镀层中石墨的含量会降低镀层与基体合金的结合强度，并导致硬度小幅下降。摩擦磨损实验结果表明，Cu/石墨复合镀层具有优良的摩擦磨损防护性能，归因于石墨有效降低了镀层的摩擦系数和磨损率；对镀层磨损形貌、磨损产物和摩擦系数的综合分析结果表明，纯铜镀层的摩擦磨损机制主要为犁削磨损、黏着磨损和剥层磨损，Cu/石墨复合镀层的磨损机制为轻微的削层磨损和疲劳磨损。     

YSZ/MoS2 self-lubricating coating fabricated by thermal spraying and hydrothermal reaction

Thermal sprayed ceramic coatings have extensively been used in components to protect them against friction and wear. However, the poor lubricating ability severely limits their application. Herein, yttria-stabilized zirconia (YSZ)/MoS₂ composite coatings were successfully fabricated on steel substrate with the combination of thermal spraying technology and hydrothermal reaction. Results show that the synthetic MoS₂ powders are composed of numbers of ultra-thin sheets (about 7 ~ 8?nm), and the sheet has obvious lamellar structure. After vacuum impregnation and hydrothermal reaction, numbers of MoS₂ powders, look like flowers, generate inside the plasma sprayed YSZ coating. Moreover, the growing point of the MoS₂ flower is the intrinsic micro-pores of YSZ coating. The friction and wear tests under high vacuum environment indicate that the composite coating has an extremely long lifetime (>?100,000 cycles) and possesses a low friction coefficient less than 0.1, which is lower by about 0.15 times than that of YSZ coating. Meanwhile, the composite shows an extremely low wear rate (2.30?×?10^?7 mm³ N^?1 m^?1) and causes slight wear damage to the counterpart. The excellent lubricant and wear-resistant ability are attributed to the formation of MoS₂ transfer films and the ultra-smooth of the worn surfaces of hybrid coatings.     

汽车发动机用AZ91D合金的表面喷涂与性能

采用热喷涂工艺在压铸态AZ91D合金表面制备了Al涂层,研究了热处理温度和保温时间对AZ91/Al涂层界面组织形貌的影响,并对比分析了扩散层的耐腐蚀性能和耐磨性能。结果表明,热处理前Al涂层与基材为机械结合,热处理后Al涂层与AZ91合金基材的界面处可形成冶金结合扩散层,且随着保温时间延长,扩散层厚度不断增加;热处理温度在375 ℃以下时扩散层主要由β-Mg₁₇Al₁₂相构成,375 ℃×8 h热处理后为α-Mg+β-Mg₁₇Al₁₂相,425 ℃×1 h热处理后为γ-Mg₂Al₃和β-Mg₁₇Al₁₂相。AZ91合金基材和扩散层腐蚀电位从高至低顺序为γ>β>α+β>AZ91合金基材,扩散层的腐蚀电流密度均低于AZ91合金基材,阻抗谱图中容抗弧半径从大至小顺序为γ>β>α+β>AZ91合金基材,扩散层的耐腐蚀性能均优于AZ91合金基材;γ、β和α+β扩散层的摩擦稳定性系数都高于AZ91合金基材,而磨损速率和磨痕宽度都要小于AZ91合金基材,其中β扩散层的磨损速率和磨痕宽度最小,具有最佳的抵抗磨损的能力。     

Effect of grinding-induced cyclic heating on the hardened layer generation in the plunge grinding of a cylindrical component

This paper discusses the effects of the grinding-induced cyclic heating on the properties of the hardened layer in a plunge cylindrical grinding process on the high strength steel EN26. It was found that a multi-pass grinding brings about a uniform and continuous hardened layer along the circumference of the cylindrical workpiece. An increase of the number of grinding passes, leads to a thicker layer of hardening, a larger compressive residual stress and a deeper plastic deformation zone. Within the plastic deformation zone, the martensitic grains are refined by the thermo-mechanical loading, giving rise to a hardness of 12.5% higher than that from a conventional martensitic transformation. The coupled effects of heat accumulation and wheel wear in the multi-pass grinding are the main causes for the thickening of the hardened layer. A too small infeed per workpiece revolution would result in insufficient grinding heat, and in turn, bring about an undesirable tempered hardened layer and a reduction of its hardness.     

A dense and compact laser cladding layer with solid metallurgical bonding significantly improved corrosion resistance of Mg alloy for engineering applications

Although Mg alloy attracts great attention for engineering applications because of high specific strength and low density, low corrosion resistance limits its extensive use. In this study, Mg–Al–Zn–Mn alloy was treated via a laser cladding process to generate a dense and compact laser cladding layer with solid metallurgical bonding on the substrate for improving corrosion resistance, effectively hindering the corrosion pervasion into Mg alloy. The corrosion current density declined from 103 μA/cm² for Mg alloy to 13 μA/cm² for the laser cladding layer in NaCl aqueous solution. Moreover, the laser cladding layer was slightly corroded in comparison with Mg alloy in NaCl aqueous solution. Besides, the microhardness of the cladding layer reached a mean value of 170.5 HV, 3.1 times of Mg alloy (56.8 HV) due to the in situ formation of hardening intermetallic phases. Wear resistance of laser cladding layer was also obviously improved. These results demonstrated that the laser cladding layer obviously enhanced anticorrosion property of Mg alloy for engineering applications.     

Tribological behaviour of a 3Y-TZP/Ta ceramic-metal biocomposite against ultrahigh molecular weight polyethylene (UHMWPE)

This study aims to evaluate the tribological behaviour of 3Y-TZP/Ta (20 vol%) ceramic-metal composites and 3Y-TZP monolithic ceramic prepared by spark plasma sintering (SPS) against ultrahigh molecular weight polyethylene (UHMWPE). According to the results of pin (UHMWPE)-on-flat wear test under dry conditions, the UHMWPE – 3Y-TZP/Ta system exhibited lower volume loss and friction coefficient than the UHMWPE – monolithic ceramic combination due to the presence of an autolubricating layer that provides sufficient lubrication for reducing the friction. Owing to the lubrication of the liquid media, under wet conditions obtained using simulated body fluid (SBF), similar behaviour is observed in both cases. Additionally, the ceramic and biocomposite materials were subjected to a low temperature degradation (LTD) process (often referred to as “ageing”) to evaluate the changes in the tribological behaviour after this treatment. In this particular case, the wear properties of the UHMWPE-biocomposite system were found to be less influenced by ageing in contrast to the case of the UHMWPE-zirconia monolithic material. In addition to their exceptional mechanical performance, 3Y-TZP/Ta composites also showed high resistance to low temperature degradation and good tribological properties, making them promising candidates for biomedical applications, especially for orthopaedic implants.